View TFF1044HN_9065426.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1. general description the TFF1044HN is a 10.70 ghz to 12.75 ghz k u band down converter for use in universal quad and quattro low noise bloc k (lnb) in satellite re ceiver systems. the device features two rf inputs (two polarizati ons) and four if outputs (up to 4 active if paths). it integrates bias generation and c ontrol for the required external lna stages, image rejection filtering, lo generation, down-conversion mixers, if amplifier stages, voltage and tone detection on each if output (for polarization and band selection) and the 4 (if channels) ? 4 (2 polarizations, 2 bands) if matr ix switch. for flexibility, the gain can be controlled in three discrete stages, the po larization of the rf inputs can be swapped and the second stage lna biasing control can be switched from phemt to bjt configuration. 2. features and benefits ? low current consumption integrated pre-amplifier, mixer, buffer amplifier and pll synthesizer ? integrated phemt/bjt bias control for external lnas ? flat gain over frequency ? single 5 v supply pin ? operates with a low cost 25 mhz crystal ? crystal-controlled lo frequency generation, alignment free concept ? dual simultaneously operating lo frequencies (9.75 ghz and 10.6 ghz) ? adjustable step gain (30 db, 33 db and 36 db) ? integrated s witch matrix ? integrated voltage and tone detector ? low phase noise ? low spurious ? low external component count ? alignment-free concept ? 36-terminal leadless plastic thermally enha nced very thin profile land grid array package 5.0 mm ? 5.0 mm ? 0.72 mm 3. applications ? quad lnbs ? quattro lnbs ? ip lnbs TFF1044HN integrated mixer oscillator pll for satellite quad lnb rev. 1 ? 10 june 2015 product data sheet + 9 / * $
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 2 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb 4. quick reference data [1] dc values. [2] see table 12 for conversion gain selection settings. 5. ordering information table 1. quick reference data v cc = 5 v; t amb = 25 ? c; f lo = 9.75 ghz or f lo = 10.6 ghz; f xtal = 25 mhz; z 0 = 50 ? for rf inputs and z 0 = 75 ? for if outputs unless otherwise specified. symbol parameter conditions min typ max unit v cc supply voltage if output ac coupled [1] 4.3 5 5.6 v i cc supply current if output ac externally coupled; excluding current for lnas; single activated if path [1] - 145 - ma f rf rf frequency 10.70 - 12.75 ghz g conv conversion gain f if = 1450 mhz (low band); single activated if path low gain mode [2] -30-db medium gain mode [2] -33-db high gain mode [2] -36-db nf ssb single sideband noise figure high gain mode; f if = 1450 mhz (low band) [2] -8-db s 11 input reflection coefficient 10.70 ghz ? f rf ? 12.75 ghz - ? 10 - db s 22 output reflection coefficient 950 mhz ? f if ? 2150 mhz - ? 10 - db ip3 o output third-order intercept point high gain mode; carrier power is ? 10 dbm (measured at if output) [2] -15-dbm table 2. ordering information type number package name description version TFF1044HN hvlga36 plastic thermal enhanced very thin profile land grid array package; no leads; 36 terminals; sot1359-1
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 3 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb 6. functional diagram fig 1. functional diagram ddd 3// /1$ %,$6 &21752/ $b'5$,1 $b*$7( $b'5$,1 $b*$7( %b*$7( %b'5$,1 %b*$7( %b'5$,1 $%b7<36(/ %b5),1 $b5),1 9 && ;23 ;21 ,)287 97,) ,)287 97,) 97,) ,)287 97,) ,)287 32/b6:$3 02'(b6(/ ++ *+] *+] 9+ +/ 9/ *$,1b6(7 3// 97,) 97,) 97,) &5<67$/ 26&,//$725 6:,7&+ 0$75,; 97,) ,) ,) ,) ,) $%b,6(7 $%b,6(7
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 4 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb 7. pinning information 7.1 pinning 7.2 pin description fig 2. pin configuration ddd 7))+1 whuplqdo lqgh[duhd $b'5$,1 $b*$7( $%b,6(7 ;23 $%b7<36(/ ;21 $%b,6(7 %b*$7( %b'5$,1 97,) 97,) ,)287 *1',) 9 && *1',) ,)287 97,) 7udqvsduhqwwrsylhz 97,) %b5)*1' %b5),1 %b5),1 %b5)*1' %b'5$,1 %b*$7( *$,1b6(7 *1',) ,)287 $b5)*1 ' $b5),1 $b5),1 $b5)*1 ' $b'5$ ,1 $b*$7 ( 32/b6: $3 02'(b 6(/ *1',) ,)287 table 3. pin description symbol pin description 1a_drain 1 drain bias for the first stage lna of rf path a 1a_gate 2 gate bias for the first stage lna of rf path a 1ab_iset 3 drain current setti ng for first stage lnas xop 4 external crystal (xtal) positive connection. connect xtal between this pin and xon (pin 6) 2ab_typsel 5 second stage lna type select: bjt/phemt xon 6 external crystal (xtal) negative conne ction. connect xtal between this pin and xop (pin 4) 2ab_iset 7 drain/collector current setting for second stage lnas 1b_gate 8 gate bias for the first stage lna of rf path b 1b_drain 9 drain bias for the first stage lna of rf path b b_rfgnd 10 rf ground of path b. connect this pin to the exposed die pad landing and the rf input transmission line b_rfin 11 rf input of path b. ac coupled; dc grounded b_rfin 12 rf input of path b. ac coupled, dc grounded b_rfgnd 13 rf ground of path b. connect this pin to the exposed die pad landing and the rf input transmission line
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 5 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb 8. limiting values 2b_drain 14 drain bias for the second stage lna of rf path b 2b_gate 15 gate bias for the second stage lna of rf path b gain_set 16 conversion gain setting pin gndif4 17 ground connection of ifout4. co nnect this pin to the exposed die pad landing and the output transmission line ground. ifout4 18 if output 4 vtif4 19 voltage and tone detector input for polarity and band selection of ifout4 vtif3 20 voltage and tone detector input for polarity and band selection of ifout3 ifout3 21 if output 3 gndif3 22 ground connection of ifout3. co nnect this pin to the exposed die pad landing and the output transmission line ground. v cc 23 supply voltage gndif2 24 ground connection of ifout2. co nnect this pin to the exposed die pad landing and the output transmission line ground. ifout2 25 if output 2 vtif2 26 voltage and tone detector input for polarity and band selection of ifout2 vtif1 27 voltage and tone detector input for polarity and band selection of ifout1 ifout1 28 if output 1 gndif1 29 ground connection of ifout1. co nnect this pin to the exposed die pad landing and the output transmission line ground. pol_swap/mode_sel 30 polarity preset for rf inputs and quad/quattro mode selection 2a_gate 31 gate bias for the second stage lna of rf path a 2a_drain 32 drain bias for the second stage lna of rf path a a_rfgnd 33 rf ground. connect this pin to the exposed die pad landing and the rf input transmission line a_rfin 34 rf input of path a. ac coupled, dc grounded a_rfin 35 rf input of path a. ac coupled, dc grounded a_rfgnd 36 rf ground. connect this pin to the exposed die pad landing and the rf input transmission line gnd exposed die pads ground; exposed die pads should be connected table 3. pin description ?continued symbol pin description table 4. limiting values in accordance with the absolute ma ximum rating system (iec 60134). symbol parameter conditions min max unit v cc supply voltage ? 0.5 +7 v v ctrl control voltage [1] [2] ? 0.5 +24 v v th(bsel)(p-p) peak-to-peak band selection threshold voltage f p(ctrl) =22khz [2] -2 v p i(rf) rf input power -0 dbm t j junction temperature - 150 ? c
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 6 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb [1] dc values. [2] on vtif1 (pin 27), vtif2 (pin 26), vtif3 (pin 20) and vtif4 (pin 19). 9. recommended operating conditions [1] dc values. [2] on vtif1 (pin 27), vtif2 (pin 26), vtif3 (pin 20) and vtif4 (pin 19). 10. thermal characteristics [1] simulated using finite element method resembli ng the device mounted in a typical application t stg storage temperature ? 40 +125 ? c v esd electrostatic discharge voltage human body model (hbm) according to ansi/esda/jedec standard js-001 - ? 2kv charged device model (cdm) according to jedec standard jesd22-c101c - ? 2kv table 4. limiting values ?continued in accordance with the absolute ma ximum rating system (iec 60134). symbol parameter conditions min max unit table 5. operating conditions symbol parameter conditions min typ max unit v cc supply voltage if output ac coupled [1] 4.3 5 5.6 v v ctrl control voltage vertical selection [1] [2] 8-14v horizontal selection [1] [2] 15.5 - 19 v v th(bsel)(p-p) peak-to-peak band selection threshold voltage high band; f p(ctrl) =22khz [2] 0.3 0.6 0.8 v t amb ambient temperature ? 40 +25 +85 ?c z 0 characteristic impedance rf inputs - 50 - ? if outputs - 75 - ? f rf rf frequency 10.70 - 12.75 ghz f lo lo frequency low band - 9.75 - ghz high band - 10.6 - ghz f if if frequency 0.95 - 2.15 ghz c l(xtal) crystal load capacitance - 16 - pf esr equivalent series resistance - - 40 ? f xtal crystal frequency - 25 - mhz table 6. thermal characteristics symbol parameter conditions typ unit r th(j-c) thermal resistance from junction to case [1] 10 k/w
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 7 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb 11. characteristics table 7. characteristics v cc = 5 v; t amb = 25 ? c; f lo = 9.75 ghz or f lo = 10.6 ghz; f xtal = 25 mhz; z 0 = 50 ? for rf inputs and z 0 = 75 ? for if outputs unless otherwise specified. symbol parameter conditions min typ max unit i cc supply current if output ac externally coupled; excluding current for lnas four activated if paths [1] -190- ma single activated if path [1] -145- ma i d drain current first stage lnas r set_12 = 22 k? connected to 1ab_iset (pin 3) 81012ma 15 k ? ? r set_12 ? 220k ? 1- 15ma second stage lnas r set_34 = 22 k? connected to 2ab_iset (pin 7) 81012ma 15 k ? ? r set_34 ? 220k ? 1- 15ma v d drain voltage first stage lnas [2] r set_12 = 22 k? 1.8 2 2.2 v 15 k ? ? r set_12 ? 220k ? 1.75 - 2.3 v no transistor attached - 2.7 - v second stage lnas (phemt) [2] [3] r set_34 = 22 k? 1.8 2 2.2 v 15 k ? ? r set_34 ? 220k ? 1.75 - 2.3 v no transistor attached - 2.7 - v v c collector voltage second stage lnas (bjt) [2] [4] r set_34 = 22 k? 1.8 2 2.2 v 15 k ? ? r set_34 ? 220k ? 1.75 - 2.3 v no transistor attached - 2.7 - v v o output voltage first stage lnas; i g =10 ? a [5] - ? 0.9 - v second stage lnas [5] second stage lna = phemt; i g = 10 ? a [3] - ? 0.9 - v second stage lna = bjt; i b = 50 ? a [4] -1.4- v g conv conversion gain f if = 1450 mhz (low band); single activated if path low gain mode [6] -30- db medium gain mode [6] -33- db high gain mode [6] -36- db f if = 1650 mhz (high band); single activated if path low gain mode [6] -30- db medium gain mode [6] -33- db high gain mode [6] -36- db
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 8 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb [1] dc values. [2] for first stage lna on 1a_drain (pin 1) or 1b_drain (pin 9) ; for second stage lna on 2a_drain (pin 32) or 2b_drain (pin 14). [3] 2ab_typsel (pin 5) is connected to gnd (phemt for second stage lnas). [4] 2ab_typsel (pin 5) is floating (bjt transistor for second stag e lnas); first stage lnas stay in the configuration for phemt biasing. [5] for first stage lna on 1a_gate (pin 2) or 1b_gate (pin 8); for second stage lna on 2a_gate (pin 31) or 2b_gate (pin 15). [6] see table 12 for conversion gain selection settings. [7] measured at low band (f if = 1450 mhz) and high band (f if = 1650 mhz); carrier power is ? 10 db m (measured at if output). [8] on vtif1 (pin 27), vtif2 (pin 26), vtif3 (pin 20) and vtif4 (pin 19). ? g conv / ? f conversion gain variation with frequency 950 mhz ? f if ? 2150 mhz - 1.0 - db in every 36 mhz band - 0.5 - db ? g conv conversion gain variation when switching from single activated if path to multiple activated if paths -1.5- db nf ssb single sideband noise figure high gain mode [6] f if = 1450 mhz (low band) - 8 - db f if = 1650 mhz (high band) - 8 - db s 11 input reflection coefficient 10.70 ghz ? f rf ? 12.75 ghz - ? 10 - db s 22 output reflection coefficient 950 mhz ? f if ? 2150 mhz - ? 10 - db p l(1db) output power at 1 db gain compression high gain mode [6] -4.5- dbm ip3 o output third-order intercept point hi gh gain mode; carrier power is ? 10 dbm (measured at if output) [6] -15- dbm ? n ? (itg)rms rms integrated phase noise density integration offset frequency = 10khzto13mhz - 1.4 - deg irr image rejection ratio [7] -17- db ? isol(ch-ch) isolation between channels [7] -30- dbc ? l(rf)lo local oscillator rf leakage f lo = 9.75 ghz - ? 48 - dbm f lo = 10.6 ghz - ? 48 - dbm ? l(if)lo local oscillator if leakage f lo = 9.75 ghz - ? 46 - dbm f lo = 10.6 ghz - ? 46 - dbm p sp spurious output power at if out puts within if band; rbw = 30 khz in the presence of the signal; carrier power is ? 10 dbm (measured at if output) -- ? 40 dbc without rf signal; input terminated with 50 ? ; medium gain mode [6] -- ? 60 dbm f p(ctrl) control pulse frequency [8] 18 22 26 khz v th(bsel)(p-p) peak-to-peak band selection threshold voltage f p(ctrl) =22khz [8] 0.3 0.6 0.8 v v th(psel) polarity selection threshold voltage [1] [8] 14 14.75 15.25 v r pd pull-down resistance on pol_swap/mode_sel (pin 30) 70 110 140 k ? on gain_set (pin 16) 70 110 140 k ? on 2ab_typsel (pin 5) 70 110 140 k ? table 7. characteristics ?continued v cc = 5 v; t amb = 25 ? c; f lo = 9.75 ghz or f lo = 10.6 ghz; f xtal = 25 mhz; z 0 = 50 ? for rf inputs and z 0 = 75 ? for if outputs unless otherwise specified. symbol parameter conditions min typ max unit
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 9 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb 11.1 impedance information 12. modes of operation 12.1 if on/off and band/polar ization control logic activation of the if paths is determined by the voltage applied at their corresponding vt pins. when the dc voltage applied to any of these pins is lower than the expected minimum value, the corresponding if path is turned off selection between vertical and horizontal polar izations for each path is determined by comparison of the dc voltage v ctrl applied at vtif pin to a reference threshold voltage. selection between high band and low band depends on the presence of a 22 khz pulse signal applied to the vtif pin for each if path . in order to improve the immunity against parasitic signals, the pulse amplitude must be larger than the threshold level for validating the switching to high-band. in these aspects, TFF1044HN is controll ed according to the logic specified in ta b l e 9 . 12.2 rf path assignment logic the vertical and horizontal polarizations are assigned to the rf path a and rf path b inputs according to the logic ta b l e 1 0 . the setting for quattro mode operation is also given in the same table. table 8. typical input impedance for smith chart see figure 27 . f z i(a_rfin) z i(b_rfin) (ghz) (? ) (? ) 10.70 52.650 + j14.850 37.350 + j18.200 11.20 64.450 + j2.900 41.850 + j19.950 11.70 62.600 ? j11.500 49.700 + j16.350 12.20 60.400 ? j13.000 59.600 + j7.250 12.75 54.950 ? j7.900 69.300 ? j10.600 table 9. if and band/polarization control voltage control pulse if path polarization band v ctrl < 4 v n/a off n/a n/a 8 v < v ctrl < 14 v no control pulse frequency; v th(bsel)(p-p) < 100 mv on vertical low f p(ctrl) = 22 khz; 300 mv < v th(bsel)(p-p) <800mv on vertical high 15.5 v < v ctrl < 19 v no control pulse frequency; v th(bsel)(p-p) < 100 mv on horizontal low f p(ctrl) = 22 khz; 300 mv < v th(bsel)(p-p) <800mv on horizontal high
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 10 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb [1] quattro mode. see table 11 for polarization and band attribution to if ports. 12.2.1 quattro mode when grounded via a 100 k ? resistor, pol_swap/mode_sel (pin 30) sets the TFF1044HN in quattro mode where the if outputs are attributed to a given polarization/band, irrespective of the signal applied to the vtif pins. each if output is assigned to a given polarization/band according to ta b l e 11 : 12.3 conversion gain selection logic the conversion gain shall be determined by the type of termination at gain_set (pin 16) following table 12 . 12.4 lna selection logic the type of transistor used for the second ln a shall be selected depending on the state of 2ab_typsel (pin 5) according to ta b l e 1 3 . table 10. polarity swap / mode selection settings connection of pol_swap/mode_sel (pin 30) mode polarity rf input path a rf input path b gnd quad horizontal vertical float quad vertical horizontal gnd via 100 k ? pull-down resistor quattro [1] n/a n/a table 11. if output assignment if output port polarization band ifout1 a_rfin low ifout2 a_rfin high ifout3 b_rfin low ifout4 b_rfin high table 12. conversion gain settings connection of gain_set (pin 16) gain mode gnd low float medium gnd via 100 k ? pull-down resistor high table 13. second stage lna type selection settings connection of 2ab_typsel (pin 5) type of second stage lna rf path a rf path b gnd phemt phemt float bjt bjt
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 11 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb 13. graphs measured from a_rfin to ifout1. low band; v cc =5v; t amb = 25 ? c. (1) high gain mode (2) medium gain mode (3) low gain mode measured from a_rfin to ifout1. high band; v cc =5v; t amb = 25 ? c. (1) high gain mode (2) medium gain mode (3) low gain mode fig 3. conversion gain as a function of rf frequency; typical values fig 4. conversion gain as a function of rf frequency; typical values measured from a_rfin to ifout2. low band; v cc =5v; t amb = 25 ? c. (1) high gain mode (2) medium gain mode (3) low gain mode measured from a_rfin to ifout2. high band; v cc =5v; t amb = 25 ? c. (1) high gain mode (2) medium gain mode (3) low gain mode fig 5. conversion gain as a function of rf frequency; typical values fig 6. conversion gain as a function of rf frequency; typical values ddd i 5) *+] * frqy frqy * frqy g% g% g% ddd i 5) *+] * frqy frqy * frqy g% g% g% ddd i 5) *+] * frqy frqy * frqy g% g% g% ddd i 5) *+] * frqy frqy * frqy g% g% g%
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 12 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb measured from b_rfin to ifout1. low band; v cc =5v; t amb = 25 ? c. (1) high gain mode (2) medium gain mode (3) low gain mode measured from b_rfin to ifout1. high band; v cc =5v; t amb = 25 ? c. (1) high gain mode (2) medium gain mode (3) low gain mode fig 7. noise figure as a function of rf frequency; typical values fig 8. noise figure as a function of rf frequency; typical values measured from b_rfin to ifout2. low band; v cc =5v; t amb = 25 ? c. (1) high gain mode (2) medium gain mode (3) low gain mode measured from b_rfin to ifout2. high band; v cc =5v; t amb = 25 ? c. (1) high gain mode (2) medium gain mode (3) low gain mode fig 9. noise figure as a function of rf frequency; typical values fig 10. noise figure as a function of rf frequency; typical values ddd i 5) *+] 1) 1) 1) g% g% g% ddd i 5) *+] 1) 1) 1) g% g% g% ddd i 5) *+] 1) 1) 1) g% g% g% ddd i 5) *+] 1) 1) 1) g% g% g%
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 13 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb v cc =5v; t amb = 25 ? c. (1) low band (2) high band fig 11. phase noise as a function of offset frequency; typical values measured from a_rfin to ifout1. high gain mode; low band; v cc =5v. (1) t amb = +85 ? c (2) t amb = +60 ? c (3) t amb = +35 ? c (4) t amb = +10 ? c (5) t amb = ?15 ? c (6) t amb = ?40 ? c measured from a_rfin to ifout1. medium gain mode; low band; v cc =5v. (1) t amb = +85 ? c (2) t amb = +60 ? c (3) t amb = +35 ? c (4) t amb = +10 ? c (5) t amb = ? 15 ? c (6) t amb = ? 40 ? c fig 12. conversion gain as a function of rf frequency; typical values fig 13. conversion gain as a function of rf frequency; typical values ddd i riivhw +] 3 q 3 q g%f+] g%f+] g%f+] ddd i 5) *+] * frqy frqy * frqy g% g% g% ddd i 5) *+] * frqy frqy * frqy g% g% g%
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 14 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb measured from a_rfin to ifout1. low gain mode; low band; v cc =5v. (1) t amb = +85 ? c (2) t amb = +60 ? c (3) t amb = +35 ? c (4) t amb = +10 ? c (5) t amb = ?15 ? c (6) t amb = ?40 ? c fig 14. conversion gain as a function of rf frequency; typical values ddd i 5) *+] * frqy frqy * frqy g% g% g%
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 15 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb measured from a_rfin to ifout1. high gain mode; high band; v cc =5v. (1) t amb = +85 ? c (2) t amb = +60 ? c (3) t amb = +35 ? c (4) t amb = +10 ? c (5) t amb = ?15 ? c (6) t amb = ?40 ? c measured from a_rfin to ifout1. medium gain mode; high band; v cc =5v. (1) t amb = +85 ? c (2) t amb = +60 ? c (3) t amb = +35 ? c (4) t amb = +10 ? c (5) t amb = ? 15 ? c (6) t amb = ? 40 ? c fig 15. conversion gain as a function of rf frequency; typical values fig 16. conversion gain as a function of rf frequency; typical values ddd i 5) *+] * frqy frqy * frqy g% g% g% ddd i 5) *+] * frqy frqy * frqy g% g% g%
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 16 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb measured from a_rfin to ifout1. low gain mode; high band; v cc =5v. (1) t amb = +85 ? c (2) t amb = +60 ? c (3) t amb = +35 ? c (4) t amb = +10 ? c (5) t amb = ?15 ? c (6) t amb = ?40 ? c fig 17. conversion gain as a function of rf frequency; typical values ddd i 5) *+] * frqy frqy * frqy g% g% g%
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 17 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb measured from b_rfin to ifout1. high gain mode; low band; v cc =5v. (1) t amb = +85 ? c (2) t amb = +60 ? c (3) t amb = +35 ? c (4) t amb = +10 ? c (5) t amb = ?15 ? c (6) t amb = ?40 ? c measured from b_rfin to ifout1. high gain mode; high band; v cc =5v. (1) t amb = +85 ? c (2) t amb = +60 ? c (3) t amb = +35 ? c (4) t amb = +10 ? c (5) t amb = ? 15 ? c (6) t amb = ? 40 ? c fig 18. noise figure as a function of rf frequency; typical values fig 19. noise figure as a function of rf frequency; typical values ddd i 5) *+] 1) 1) 1) g% g% g% ddd i 5) *+] 1) 1) 1) g% g% g%
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 18 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb measured from a_rfin to ifout1. low band; single activated if path; v cc =5v; t amb =25 ? c; tone separation = 33 mhz. (1) high gain mode (2) medium gain mode (3) low gain mode measured from a_rfin to ifout1. high band; single activated if path; v cc =5v; t amb =25 ? c; tone separation = 33 mhz. (1) high gain mode (2) medium gain mode (3) low gain mode fig 20. output third-order intercept point as a function of if frequency; typical values fig 21. output third-order in tercept point as a function of if frequency; typical values measured from a_rfin to ifout1. low band; high gain mode; v cc =5v; t amb =25 ? c; tone separation = 33 mhz. (1) 1 activated if path (2) 2 activated if paths (3) 3 activated if paths (4) 4 activated if paths measured from a_rfin to ifout1. high band; high gain mode; v cc =5v; t amb =25 ? c; tone separation = 33 mhz. (1) 1 activated if path (2) 2 activated if paths (3) 3 activated if paths (4) 4 activated if paths fig 22. output third-order intercept point as a function of if frequency; typical values fig 23. output third-order in tercept point as a function of if frequency; typical values ddd i ,) *+] ,3 ,3 r ,3 r g%p g%p g%p ddd i ,) *+] ,3 ,3 r ,3 r g%p g%p g%p ddd i ,) *+] ,3 ,3 r ,3 r g%p g%p g%p ddd i ,) *+] ,3 ,3 r ,3 r g%p g%p g%p
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 19 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb low band; high gain mode; v cc =5v; t amb =25 ? c. (1) rf input path b to rf input path a (2) rf input path a to rf input path b high band; high gain mode; v cc =5v; t amb =25 ? c. (1) rf input path b to rf input path a (2) rf input path a to rf input path b fig 24. isolation between channels as a function of rf frequency; typical values fig 25. isolation between channels as a function of rf frequency; typical values v cc =5v. (1) low band (2) high band fig 26. rms integrated phase noise density as a function of ambient temperature; typical values ddd i 5) *+] . lvrofkfk lvrofkfk . lvrofkfk g%f g%f g%f ddd i 5) *+] . lvrofkfk lvrofkfk . lvrofkfk g%f g%f g%f ddd 7 dpe ?& 3 qlwj506 qlwj506 3 qlwj506 ghj ghj ghj
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 20 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb (1) f rf = 10.70 ghz (2) f rf = 12.75 ghz fig 27. input reflection coefficient (s 11 ); typical values ? ddd $b5),1 $b5),1 $b5),1 %b5),1 %b5),1 %b5),1
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 21 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb 14. application information for more information see application note an11640 fig 28. lnb system block diagram with TFF1044HN ddd 3// /1$ %,$6 &21752/ $b'5$,1 $b*$7( $b'5$,1 $b*$7( %b*$7( %b'5$,1 %b*$7( %b'5$,1 $%b7<36(/ /1$ /1$ 5)lqsxwsdwk% 9 && ;23 ;21 ,)287 0+] 97,) ,)287 97,) 97,) ,)287 97,) ,)287 32/b6:$3 02'(b6(/ ++ *+] *+] 9+ +/ 9/ *$,1b6(7 3// 97,) 97,) 97,) &5<67$/ 26&,//$725 6:,7&+ 0$75,; 97,) ,) ,) ,) ,) 9 5(*8/$725 ,)287 9 && uhj 9 5(*8/$725 ,)287 9 && uhj 9 5(*8/$725 9 && uhj yhuwl fdokrul]rqwdo srodulvdwlrq ,)287 9 5(*8/$725 9 && uhj ,)287 /1$ /1$ 5)lqsxwsdwk$ krul ]rqwdoyhuwlfdo srodulvdwlrq 9 && uhj 9 && 9 %$9 ruhtxlydohqw 9 9 9 9 9 && uhj 9 && uhj 9 && uhj $%b7<36(/ *1'/1$dqg/1$ 3+(07 iordw/1$dqg/1$ %-7 32/b6:$302'(b6(/ 5sgtxdwwur iordw5)lqsxwsdwk$ yhuwlfdo5)lqsxwsdwk% krul]rqw do *1'5)lqsxwsdwk$ krul]rqwdo5)lqsxwsdwk% yhuwlfdo *$,1b6(7 5sgkljkjdlq iordwphglxpjdlq *1'orzjdlq %-73+(07
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 22 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb fig 29. application diagram of TFF1044HN 7))+1 $b'5$,1 $b*$7( $%b,6(7 ;23 $%b7<36(/ ;21 $%b,6(7 %b*$7( %b'5$,1 97,) 9 5(*8/$725 ,) 9 && uhj 9 r 9 l 97,) ,)287 *1',) 9 && *1',) ,)287 97,) 97,) %b5)*1' %-73+(07 plfurzdyh udgldovwxe /1$ /1$ ddd %b5),1 %b5),1 %b5)*1' %b'5$,1 %b*$7( *$,1b6(7 *1',) ,)287 $b5)*1' $b5),1 $b5),1 $b5)*1' $b'5$,1 $b*$7( 32/b6:$302'(b6(/ *1',) ,)287 9 5(*8/$725 ,) 9 && uhj 9 && 9 r 9 l 9 5(*8/$725 ,) 9 && uhj 9 r 9 l 9 5(*8/$725 ,) 9 && uhj 9 r 9 l /1$ /1$ +9 9+ plfurzdyh udgldovwxe 5 vhwb 5 vhwb 5 sg 0+] 5)lqsxwsdwk$ 5)lqsxwsdwk% plfurzdyh udgldovwxe plfurzdyh udgldovwxe %-73+(07 9 && uhj 9 & & 9 %$9 ruhtxlydohqw 9 9 9 9 9 && uhj 9 && uhj 9 && uhj
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 23 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb 15. package outline fig 30. package outline sot1359-1 (hvlga36) 5hihuhqfhv 2xwolqh yhuvlrq (xurshdq surmhfwlrq ,vvxhgdwh ,(& -('(& -(,7$ 627 vrwbsr 8qlw pp pd[ qrp plq $ 'lphqvlrqvppduhwkhruljlqdoglphqvlrqv +9/*$sodvwlfwkhupdohqkdqfhgyhu\wklqsurilohodqgjulgduud\sdfndjhqrohdgvwhuplqdov 627 e' ' k ' v ' w ( k ( k ( v ( w h $ ' k ' k ' k ( ( k ( k h h // yz \\ vfdoh pp ; & \ & \ ( % ' $ ' k ' k ' k ' k ghwdlo; h h ' v ' w e $& % y & z ( k ( k ( k / / ( w ( k ( v h h $ $ whuplqdo lqgh[duhd whuplqdo lqgh[duhd
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 24 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb 16. abbreviations 17. revision history table 14. abbreviations acronym description bjt bipolar junction transistor hh horizontal high band hl horizontal low band if intermediate frequency ip internet protocol k u band k-under band lna low noise amplifier lnb low noise block lo local oscillator phemt pseudomorphic high electron mobility transistor pll phase-locked loop rbw resolution bandwidth vh vertical high band vl vertical low band vt voltage tone table 15. revision history document id release date data sheet status change notice supersedes TFF1044HN v.1 20150610 product data sheet - -
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 25 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb 18. legal information 18.1 data sheet status [1] please consult the most recently issued document before initiating or completing a design. [2] the term ?short data sheet? is explained in section ?definitions?. [3] the product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple device s. the latest product status information is available on the internet at url http://www.nxp.com . 18.2 definitions draft ? the document is a draft versi on only. the content is still under internal review and subject to formal approval, which may result in modifications or additions. nxp semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall hav e no liability for the consequences of use of such information. short data sheet ? a short data sheet is an extract from a full data sheet with the same product type number(s) and title. a short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. for detailed and full information see the relevant full data sheet, which is available on request vi a the local nxp semiconductors sales office. in case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. product specification ? the information and data provided in a product data sheet shall define the specification of the product as agreed between nxp semiconductors and its customer , unless nxp semiconductors and customer have explicitly agreed otherwis e in writing. in no event however, shall an agreement be valid in which the nxp semiconductors product is deemed to offer functions and qualities beyond those described in the product data sheet. 18.3 disclaimers limited warranty and liability ? information in this document is believed to be accurate and reliable. however, nxp semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such info rmation. nxp semiconductors takes no responsibility for the content in this document if provided by an information source outside of nxp semiconductors. in no event shall nxp semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. notwithstanding any damages that customer might incur for any reason whatsoever, nxp semiconductors? aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the terms and conditions of commercial sale of nxp semiconductors. right to make changes ? nxp semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. this document supersedes and replaces all information supplied prior to the publication hereof. suitability for use ? nxp semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an nxp semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. nxp semiconductors and its suppliers accept no liability for inclusion and/or use of nxp semiconducto rs products in such equipment or applications and therefore such inclusion and/or use is at the customer?s own risk. applications ? applications that are described herein for any of these products are for illustrative purpos es only. nxp semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. customers are responsible for the design and operation of their applications and products using nxp semiconductors products, and nxp semiconductors accepts no liability for any assistance with applications or customer product design. it is customer?s sole responsibility to determine whether the nxp semiconductors product is suitable and fit for the customer?s applications and products planned, as well as fo r the planned application and use of customer?s third party customer(s). customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. nxp semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer?s applications or products, or the application or use by customer?s third party customer(s). customer is responsible for doing all necessary testing for the customer?s applic ations and products using nxp semiconductors products in order to av oid a default of the applications and the products or of the application or use by customer?s third party customer(s). nxp does not accept any liability in this respect. limiting values ? stress above one or more limiting values (as defined in the absolute maximum ratings system of iec 60134) will cause permanent damage to the device. limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the recommended operating conditions section (if present) or the characteristics sections of this document is not warranted. constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. terms and conditions of commercial sale ? nxp semiconductors products are sold subject to the gener al terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. in case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. nxp semiconductors hereby expressly objects to applying the customer?s general terms and conditions with regard to the purchase of nxp semiconducto rs products by customer. no offer to sell or license ? nothing in this document may be interpreted or construed as an offer to sell products t hat is open for acceptance or the grant, conveyance or implication of any lic ense under any copyrights, patents or other industrial or intellectual property rights. document status [1] [2] product status [3] definition objective [short] data sheet development this document contains data from the objecti ve specification for product development. preliminary [short] data sheet qualification this document contains data from the preliminary specification. product [short] data sheet production this document contains the product specification.
TFF1044HN all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2015. all rights r eserved. product data sheet rev. 1 ? 10 june 2015 26 of 27 nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb export control ? this document as well as the item(s) described herein may be subject to export control regu lations. export might require a prior authorization from competent authorities. non-automotive qualified products ? unless this data sheet expressly states that this specific nxp semicon ductors product is automotive qualified, the product is not suitable for automotive use. it is neither qualified nor tested in accordance with automotive testing or application requirements. nxp semiconductors accepts no liabili ty for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. in the event that customer uses t he product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without nxp semiconductors? warranty of the product for such automotive applicat ions, use and specifications, and (b) whenever customer uses the product for automotive applications beyond nxp semiconductors? specifications such use shall be solely at customer?s own risk, and (c) customer fully in demnifies nxp semi conductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive app lications beyond nxp semiconductors? standard warranty and nxp semiconduct ors? product specifications. quick reference data ? the quick reference data is an extract of the product data given in the limiting values and characteristics sections of this document, and as such is not comp lete, exhaustive or legally binding. translations ? a non-english (translated) version of a document is for reference only. the english version shall prevail in case of any discrepancy between the translated and english versions. 18.4 trademarks notice: all referenced brands, produc t names, service names and trademarks are the property of their respective owners. 19. contact information for more information, please visit: http://www.nxp.com for sales office addresses, please send an email to: salesaddresses@nxp.com
nxp semiconductors TFF1044HN integrated mixer oscillator pll for satellite quad lnb ? nxp semiconductors n.v. 2015. all rights reserved. for more information, please visit: http://www.nxp.com for sales office addresses, please se nd an email to: salesaddresses@nxp.com date of release: 10 june 2015 document identifier: TFF1044HN please be aware that important notices concerning this document and the product(s) described herein, have been included in section ?legal information?. 20. contents 1 general description . . . . . . . . . . . . . . . . . . . . . . 1 2 features and benefits . . . . . . . . . . . . . . . . . . . . 1 3 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 quick reference data . . . . . . . . . . . . . . . . . . . . . 2 5 ordering information . . . . . . . . . . . . . . . . . . . . . 2 6 functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 7 pinning information . . . . . . . . . . . . . . . . . . . . . . 4 7.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 7.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 8 limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5 9 recommended operating conditions. . . . . . . . 6 10 thermal characteristics . . . . . . . . . . . . . . . . . . 6 11 characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 7 11.1 impedance information . . . . . . . . . . . . . . . . . . . 9 12 modes of operation . . . . . . . . . . . . . . . . . . . . . . 9 12.1 if on/off and band/polarization control logic . . . 9 12.2 rf path assignment logic . . . . . . . . . . . . . . . . . 9 12.2.1 quattro mode . . . . . . . . . . . . . . . . . . . . . . . . . 10 12.3 conversion gain selection logic . . . . . . . . . . . 10 12.4 lna selection logic . . . . . . . . . . . . . . . . . . . . . 10 13 graphs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 14 application information. . . . . . . . . . . . . . . . . . 21 15 package outline . . . . . . . . . . . . . . . . . . . . . . . . 23 16 abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 24 17 revision history . . . . . . . . . . . . . . . . . . . . . . . . 24 18 legal information. . . . . . . . . . . . . . . . . . . . . . . 25 18.1 data sheet status . . . . . . . . . . . . . . . . . . . . . . 25 18.2 definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 18.3 disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 18.4 trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 26 19 contact information. . . . . . . . . . . . . . . . . . . . . 26 20 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

▲Up To Search▲

Price & Availability of TFF1044HN

	To Download TFF1044HN Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .